Please note that Greenfield Village will close at 3 p.m. on Friday, September 11, but have extended hours until 9 p.m. on Saturday, September 12 for Old Car Festival.

Please note that Greenfield Village will close at 3 p.m. on Friday, September 11, but have extended hours until 9 p.m. on Saturday, September 12 for Old Car Festival.

The Wright Brothers and the Bicycle Business

Written by
Saige JedeleMatt Anderson
Saige Jedele is a former associate curator, digital content, for The Henry Ford
Matt Anderson is curator of transportation at The Henry Ford.
THF112383
Before they took flight, Wilbur and Orville Wright dealt in bicycles. The brothers repaired, rented, built and sold bikes in Dayton, Ohio. The Wrights used concepts, skills and profits from their cycle company to support their aviation experiments.
THF236856

Wright Cycle Shop in Dayton, Ohio, circa 1910

The Wright brothers operated their bicycle business at six different Dayton, Ohio, locations from 1892 to 1908. They occupied this building, at 1127 West Third Street, from 1897 to 1908. It was here that the brothers conducted their first serious aviation experiments and built their gliders and the 1903 Wright Flyer — the first successful heavier-than-air powered aircraft.

View Artifact

Lathe, Used by the Wright Brothers, circa 1895

The Wright brothers' bicycle shop contained several large power tools primarily used for making and repairing bikes. Some were also used to build their early gliders and airplanes. The shop building did not have electricity, so the Putnam lathe, Crescent band saw and Barnes drill press were powered by overhead belts and shafts connected to a single-cylinder gas engine.
View Artifact

Wright Cycle Shop

Wilbur and Orville Wright operated their bicycle business in this building from 1897 to 1908 in Dayton, Ohio. The brothers sold and repaired bikes, and they even produced models under their own brands. It was also in this shop that the Wright brothers built their earliest flying machines, including the 1903 Flyer that became the first successful heavier-than-air, powered, controlled aircraft.
View Artifact

Drill Press, Used by the Wright Brothers, circa 1895

The Wright brothers' bicycle shop contained several large power tools primarily used for making and repairing bikes. Some were also used to build their early gliders and airplanes. The shop building did not have electricity, so the Putnam lathe, Crescent band saw and Barnes drill press were powered by overhead belts and shafts connected to a single-cylinder gas engine.
View Artifact

Van Cleve Bicycle, Made by the Wright Brothers circa 1896

Wilbur and Orville Wright established their first bicycle shop in 1892. They started building their own bikes in 1896. Van Cleve bicycles — named for Wright family ancestors — used high-grade materials, and they featured special oil-retaining wheel hubs and coaster brakes of the brothers' own design. The Wrights built each bike to order, hand-making parts with basic tools.

View Artifact

Catalog for Van Cleve Bicycles, Wright Cycle Company, 1900

Wilbur and Orville Wright established their first bicycle shop in 1892. They started building their own bikes in 1896. Van Cleve bicycles — named for Wright family ancestors — used high-grade materials, and they featured special oil-retaining wheel hubs and coaster brakes of the brothers' own design. The Wrights built each bike to order, hand-making parts with basic tools.

View Artifact

Bicycle Spokes, Used by the Wright Brothers, Dayton, Ohio, circa 1900

Wilbur and Orville Wright ran their bicycle business from 1892-1908. Wright Cycle Company operated at five different Dayton, Ohio, locations before settling at 1127 West Third Street in 1897. The Wrights sold and repaired bikes, and they carried a full line of cycling accessories and supplies. For a few years, the brothers even built bicycles under their own brands.
View Artifact

St. Clair Bicycle Made by the Wright Brothers, 1897-1901

After their 1901 glider didn't perform as expected, Wilbur and Orville Wright modified a bicycle to test the data used to shape their wings. Riding the bike generated a breeze that simulated the air pressure against a wing in flight. Although this St. Clair bicycle was built by the Wrights, it is not the actual bike used in their experiments.
View Artifact

Orville Wright and Edwin H. Sines in Wright Cycle Shop, Dayton, Ohio, 1897

Orville Wright (right) was photographed alongside friend and former schoolmate Edwin H. Sines in the Wright brothers' Dayton, Ohio, bicycle shop. The Wrights' experiences building printing presses and bicycles sharpened their skills in precision machining. These talents were invaluable in their later efforts to build the first successful heavier-than-air, powered aircraft in 1903.
View Artifact

Band Saw, Used by the Wright Brothers, circa 1899

The Wright brothers' bicycle shop contained several large power tools primarily used for making and repairing bikes. Some were also used to build their early gliders and airplanes. The shop building did not have electricity, so the Putnam lathe, Crescent band saw and Barnes drill press were powered by overhead belts and shafts connected to a single-cylinder gas engine.
View Artifact